lilylu@huisins.com     86-13922763266
  • Aliphatic polyurethane finish
  • Aliphatic polyurethane finish
  • Aliphatic polyurethane finish
Aliphatic polyurethane finishAliphatic polyurethane finishAliphatic polyurethane finish

Aliphatic polyurethane finish

  • Product Item : 725-S52-60
  • Category: Industrial Coatings
  • A two pack acrylic polyurethane finish giving excellent durability and long term recoatability.
  • For use in offshore structure environment ,such as petrochemical plants, marine engineering,chemical plants, power stations, bridges and industrial buildings.
  • TDS INQUIRY   EMAIL

Product Description:

- Model:725-S52-60

-A two pack acrylic polyurethane finish giving excellent durability and long term recoatability

-High Volume Solids

-Pass the test of NORSOK M501

-VOC less than 250g/L

Intended Uses:

-A tough cosmetic finish.

-For use in offshore structure environment such as petrochemical plants, chemical plants, power stations, bridges and industrial buildings.

-For marine engineering.

Product Information:

Volume Solids:72%±2% Finish/Sheen Gloss

Film Thickness and Theoretical Coverage

Min

Typical

Max

Dryfilm Thickness(μm)

40

80

100

Wetfilm Thickness(μm)

55

111

139

Theoretical Coverage(m²/L)

18

9

7.2

Mix Ratio: 7:1(volume) 10:1(mass)

Method of Application

Airless Spray

Recommended

Tip size range:0.38-0.53mm

Output pressure:17MPa

Air Spray

Tip size range:2.0-3.0mm

Output pressure:0.4MPa

Brush/Roller

For small area only

Thinner

Not recommended.Use only in exceptional circumstances (volume 5%).

Cleaner

725-BX-28

Induction Period

Not required

Drying Information:


-5

5

25

35

Touch Dry

4h

2h

40min

30min

Hard Dry

48h

24h

8h

6h

Pot Life

8h

6h

4h

4h

Overcoating Data:

-5

5

25

35

Overcoated by

Min Max

Min Max

Min Max

Min Max

725-S52-60

48h /

24h /

8h /

6h /

Storage:

Store in cool and dry conditions,Well ventilate.Keep away from hot and fire. Shelf Life: 12 months

minimum at 25,Subject to re-inspection thereafter.

Pack Size:

Part A: 23kg/17L in 20 L container

Part B: 2.3kg/2.5L in 6L container

Flash Point:

Part A: Greater than 31℃

Part B: Greater than 28

Mixed pant: Greater than 31℃

Systems and Compatibility:

Consult your Representative for the systems best suited for the surfaces to be protected.

Surface Preparation:

All surfaces to be coated should be clean, dry and free from contamination.

Primed Surfaces

The primer surface should be dry free from all contamination and 725-S52-60must be applied within the overcoating intervals specified (consult the relevantproduct data sheet).

Areas of breakdown, damage etc., should be prepared to the specified standard (e.gSa2.5GB/T 8923.1-2011or Abrasive Blasting, or Power Tool Cleaning) and patchprimed prior to the application of 725-S52-60.

Repair

725-S52-60 should be applied over a recommended primer coating scheme. The primer  surface should be clean, dry and free from contamination. Areas of breakdown, damage etc. should be prepared to the specified standard (eg. Sa2.5) and primed prior to the application of 725-S52-60.

725-S52-60may be applied directly over aged 725-S52-60 following thorough fresh water washing and degreasing provided the coating to be overcoated is in an intact and tightly adherent condition. Loose or flaking coatings should be removed back to a firm edge and an appropriate primer should be used to repair the area before application of the full coat.

CONTACT US

Name: Lily Lu

Mobile:86-13922763266

Tel:86-20-38993165

Whatsapp:86-13922763266

Email:lilylu@huisins.com

Add:Room 206, Building 21, LongTeng Xing Cheng, No.68 LongTeng South Road, DongXiao Town, XinLuo District, LongYan City, FuJian Province. China